Month: November 2013

Cisco 5508 Wireless LAN controller: Enable Web access from GUI

Posted on


(Cisco Controller) >config network webmode enable

(Cisco Controller) >config network secureweb enable
You must reboot for the change to take effect.

(Cisco Controller) >reset system

The system has unsaved changes.
Would you like to save them now? (y/N) y

Configuration Saved!

Reset Cisco WLC 5508 to factory settings

Posted on


(Cisco Controller) >reset system

The system has unsaved changes.
Would you like to save them now? (y/N) y

Configuration Saved!
System will now restart! Restarting system.

WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)
Board Revision 1.3 (SN: XXXXX, Type: AIR-CT5508-K9) (G)

Verifying boot loader integrity… OK.

OCTEON CN5645-NSP pass 2.1, Core clock: 600 MHz, DDR clock: 330 MHz (660 Mhz data rate)
FPGA Revision 1.7
Env FW Revision 1.8
USB Console Revision 2.2
CPU Cores: 10
DRAM: 1024 MB
Flash: 32 MB
Clearing DRAM…….. done
Network: octeth0′, octeth1
‘ – Active interface
E – Environment MAC address override
CF Bus 0 (IDE): OK
IDE device 0:
– Model: STEC M2T CF 1.0.0 Firm: K1367MIX Ser#:
– Type: Hard Disk
– Capacity: 977.4 MB = 0.9 GB (2001888 x 512)

Press <ESC> now to access the Boot Menu…

Loading primary image (7.5.102.0)
100%

35801606 bytes read
Launching…
init started: BusyBox v1.6.0 (2010-05-13 17:50:10 EDT) multi-call binary
starting pid 826, tty ”: ‘/etc/init.d/rcS’

Set PLX switch MPS settings ………….!!!!!!!
Detecting Hardware …
set smp_affinity for irq 48
003f
DP from CGE5.0 …
starting pid 1072, tty ‘/dev/ttyS0’: ‘/usr/bin/gettyOrMwar’
Setting up ZVM
Exporting LD_LIBRARY_PATH

Cryptographic library self-test….passed!
XML config selected
Validating XML configuration
Read HA Config before validation
octeon_device_init: found 1 DPs
readCPUConfigData: cardid 0x6070001
Cisco is a trademark of Cisco Systems, Inc.
Software Copyright Cisco Systems, Inc. All rights reserved.

Cisco AireOS Version 7.5.102.0
Firmware Version FPGA 1.7, Env 1.8, USB console 2.2
Initializing OS Services: ok
Initializing Serial Services: ok
Initializing Network Services: ok
Initializing Licensing Services: ok

License daemon start initialization…..

License daemon running…..
Starting Statistics Service: ok
Starting ARP Services: ok
Starting Trap Manager: ok
Starting Network Interface Management Services: ok
Starting System Services: ok
Starting FIPS Features: ok : Not enabled
Starting Fastpath Hardware Acceleration: ok
Starting Fastpath Console redirect : ok
Starting Fastpath DP Heartbeat : ok
Fastpath CPU0.00: Starting Fastpath Application. SDK-1.8.0, build 269. Flags-[DUTY CYCLE] : ok
Fastpath CPU0.00: Initializing last packet received queue. Num of cores(10)
Fastpath CPU0.00: Init MBUF size: 1856, Subsequent MBUF size: 2040
Fastpath CPU0.00: Core 0 Initialization and FIPS self-test: ok
Fastpath CPU0.00: Initializing Timer…
Fastpath CPU0.00: Initializing Timer…done.
Fastpath CPU0.00: Initializing Timer…
Fastpath CPU0.00: Initializing NBAR AGING Timer…done.
Fastpath CPU0.01: Core 1 Initialization and FIPS self-test: ok
Fastpath CPU0.02: Core 2 Initialization and FIPS self-test: ok
Fastpath CPU0.03: Core 3 Initialization and FIPS self-test: ok
Fastpath CPU0.03: Received instruction to get link status
Fastpath CPU0.04: Core 4 Initialization and FIPS self-test: ok
Fastpath CPU0.05: Core 5 Initialization and FIPS self-test: ok
Fastpath CPU0.06: Core 6 Initialization and FIPS self-test: ok
Fastpath CPU0.07: Core 7 Initialization and FIPS self-test: ok
Fastpath CPU0.08: Core 8 Initialization and FIPS self-test: ok
Fastpath CPU0.09: Core 9 Initialization and FIPS self-test: ok
Starting Switching Services: ok
Starting QoS Services: ok
Starting Policy Manager: ok
Starting Data Transport Link Layer: ok
Starting Access Control List Services: ok
Starting System Interfaces: ok
Starting Client Troubleshooting Service: ok
Starting Management Frame Protection: ok
Starting Certificate Database: ok
Starting VPN Services: ok
Starting DNS Services: ok
Starting Licensing Services: ok
Starting Redundancy: ok
Starting LWAPP: ok
Starting CAPWAP: ok
Starting LOCP: ok
Starting Security Services: ok
Starting Policy Manager: ok
Starting Authentication Engine: ok
Starting Mobility Management: ok
Starting Capwap Ping Component: ok
Starting AVC Services: ok
Starting Virtual AP Services: ok
Starting AireWave Director: ok
Starting Network Time Services: ok
Starting Cisco Discovery Protocol: ok
Starting Broadcast Services: ok
Starting Logging Services: ok
Starting DHCP Server: ok
Starting IDS Signature Manager: ok
Starting RFID Tag Tracking: ok
Starting RF Profiles: ok
Starting Power Supply and Fan Status Monitoring Service: ok
Starting Mesh Services: ok
Starting TSM: ok
Starting CIDS Services: ok
Starting Ethernet-over-IP: ok
Starting DTLS server: enabled in CAPWAP
Starting CleanAir: ok
Starting WIPS: ok
Starting SSHPM LSC PROV LIST: ok
Starting RRC Services: ok
Starting SXP Services: ok
Starting Alarm Services: ok
Starting FMC HS: ok
Starting IPv6 Services: ok
Starting Config Sync Manager : ok

You have been idle for 150 seconds. Your session will end in 150 seconds.

Starting Hotspot Services: ok
Starting PMIP Services: ok
Starting Portal Server Services: ok
Starting mDNS Services: ok
Starting Management Services:
Web Server: CLI: Secure Web: ok

(Cisco Controller)

Enter User Name (or ‘Recover-Config’ this one-time only to reset configuration to factory defaults)

User: recover-configInitiating system recovery process… please wait

Writing to flash …done

Rebooting system
Restarting system.

WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)
Board Revision 1.3 (SN: , Type: AIR-CT5508-K9) (G)

Verifying boot loader integrity… OK.

OCTEON CN5645-NSP pass 2.1, Core clock: 600 MHz, DDR clock: 330 MHz (660 Mhz data rate)
FPGA Revision 1.7
Env FW Revision 1.8
USB Console Revision 2.2
CPU Cores: 10
DRAM: 1024 MB
Flash: 32 MB
Clearing DRAM…….. done
Network: octeth0′, octeth1
‘ – Active interface
E – Environment MAC address override
CF Bus 0 (IDE): OK
IDE device 0:
– Model: STEC M2T CF 1.0.0 Firm: K1367MIX Ser#:
– Type: Hard Disk
– Capacity: 977.4 MB = 0.9 GB (2001888 x 512)

Press <ESC> now to access the Boot Menu…

Loading primary image (7.5.102.0)
100%

35801606 bytes read
Launching…
init started: BusyBox v1.6.0 (2010-05-13 17:50:10 EDT) multi-call binary
starting pid 826, tty ”: ‘/etc/init.d/rcS’

Set PLX switch MPS settings ………….!!!!!!!
Detecting Hardware …
set smp_affinity for irq 48
003f
DP from CGE5.0 …
starting pid 1075, tty ‘/dev/ttyS0’: ‘/usr/bin/gettyOrMwar’
Setting up ZVM
Exporting LD_LIBRARY_PATH

Cryptographic library self-test….passed!
XML config selected
Validating XML configuration
octeon_device_init: found 1 DPs
readCPUConfigData: cardid 0x6070001

XML Config version file is corrupted :Move all files to tmp XML dir

XML config version file is corrupted: Removed xml dir
XML validation can not be done file open failed
sh: cannot create /mnt/application/xml/clis/XMLInvalidTagConfig.txt: nonexistent directory
Cisco is a trademark of Cisco Systems, Inc.
Software Copyright Cisco Systems, Inc. All rights reserved.

Cisco AireOS Version 7.5.102.0
Firmware Version FPGA 1.7, Env 1.8, USB console 2.2
Initializing OS Services: ok
Initializing Serial Services: ok
Initializing Network Services: ok
Initializing Licensing Services: ok

License daemon start initialization…..

License daemon running…..
Starting Statistics Service: ok
Starting ARP Services: ok
Starting Trap Manager: ok
Starting Network Interface Management Services: ok
Starting System Services: ok
Starting FIPS Features: ok : Not enabled
Starting Fastpath Hardware Acceleration: ok
Starting Fastpath Console redirect : ok
Starting Fastpath DP Heartbeat : ok
Fastpath CPU0.00: Starting Fastpath Application. SDK-1.8.0, build 269. Flags-[DUTY CYCLE] : ok
Fastpath CPU0.00: Initializing last packet received queue. Num of cores(10)
Fastpath CPU0.00: Init MBUF size: 1856, Subsequent MBUF size: 2040
Fastpath CPU0.00: Core 0 Initialization and FIPS self-test: ok
Fastpath CPU0.00: Initializing Timer…
Fastpath CPU0.00: Initializing Timer…done.
Fastpath CPU0.00: Initializing Timer…
Fastpath CPU0.00: Initializing NBAR AGING Timer…done.
Fastpath CPU0.01: Core 1 Initialization and FIPS self-test: ok
Fastpath CPU0.02: Core 2 Initialization and FIPS self-test: ok
Fastpath CPU0.03: Core 3 Initialization and FIPS self-test: ok
Fastpath CPU0.03: Received instruction to get link status
Fastpath CPU0.04: Core 4 Initialization and FIPS self-test: ok
Fastpath CPU0.05: Core 5 Initialization and FIPS self-test: ok
Fastpath CPU0.06: Core 6 Initialization and FIPS self-test: ok
Fastpath CPU0.07: Core 7 Initialization and FIPS self-test: ok
Fastpath CPU0.08: Core 8 Initialization and FIPS self-test: ok
Fastpath CPU0.09: Core 9 Initialization and FIPS self-test: ok
Starting Switching Services: ok
Starting QoS Services: ok
Starting Policy Manager: ok
Starting Data Transport Link Layer: ok
Starting Access Control List Services: ok
Starting System Interfaces: ok
Starting Client Troubleshooting Service: ok
Starting Management Frame Protection: ok
Starting Certificate Database: ok
Starting VPN Services:

You have been idle for 150 seconds. Your session will end in 150 seconds.

ok
Starting DNS Services: ok
Starting Licensing Services: ok
Starting Redundancy: ok
Starting LWAPP: ok
Starting CAPWAP: ok
Starting LOCP: ok
Starting Security Services: ok
Starting Policy Manager: ok
Starting Authentication Engine: ok
Starting Mobility Management: ok
Starting Capwap Ping Component: ok
Starting AVC Services: ok
Starting Virtual AP Services: ok
Starting AireWave Director: ok
Starting Network Time Services: ok
Starting Cisco Discovery Protocol: ok
Starting Broadcast Services: ok
Starting Logging Services: ok
Starting DHCP Server: ok
Starting IDS Signature Manager: ok
Starting RFID Tag Tracking: ok
Starting RF Profiles: ok
Starting Power Supply and Fan Status Monitoring Service: ok
Starting Mesh Services: ok
Starting TSM: ok
Starting CIDS Services: ok
Starting Ethernet-over-IP: ok
Starting DTLS server: enabled in CAPWAP
Starting CleanAir: ok
Starting WIPS: ok
Starting SSHPM LSC PROV LIST: ok
Starting RRC Services: ok
Starting SXP Services: ok
Starting Alarm Services: ok
Starting FMC HS: ok
Starting IPv6 Services: ok
Starting Config Sync Manager : ok
Starting Hotspot Services: ok
Starting PMIP Services: ok
Starting Portal Server Services: ok
Starting mDNS Services: ok
Starting Management Services:
Web Server: CLI: Secure Web: Web Authentication Certificate not found (error). If you cannot access management interface via HTTPS please reconfigure Virtual Interface.

(Cisco Controller)

Welcome to the Cisco Wizard Configuration Tool
Use the ‘-‘ character to backup

Would you like to terminate autoinstall? [yes]:

System Name [Cisco_f9:38:c4] (31 characters max):
AUTO-INSTALL: process terminated — no configuration loaded

Enter Administrative User Name (24 characters max):
Invalid response

Enter Administrative User Name (24 characters max): XXXXXXX
Enter Administrative Password (3 to 24 characters): ********
Re-enter Administrative Password : ********

Service Interface IP Address Configuration [static][DHCP]: 192.168.40.1
Invalid response

Service Interface IP Address Configuration [static][DHCP]: st
Invalid response

Service Interface IP Address Configuration [static][DHCP]: static
Service Interface IP Address: 192.168.40.1
Service Interface Netmask: 255.255.255.0

Enable Link Aggregation (LAG) [yes][NO]: no

Management Interface IP Address: 172.20.74.184
Management Interface Netmask: 255.255.254.0
Management Interface Default Router: 172.20.74.2
Management Interface VLAN Identifier (0 = untagged): 0
Management Interface Port Num [1 to 8]: 7
Management Interface DHCP Server IP Address:
Invalid response

Management Interface DHCP Server IP Address: 172.20.74.184

Enable HA (Dedicated Redundancy Port is used by Default) [yes][NO]: no

Virtual Gateway IP Address: 1.1.1.1

Mobility/RF Group Name: XXXXXXXX

Network Name (SSID): TEST

Configure DHCP Bridging Mode [yes][NO]: no

Allow Static IP Addresses [YES][no]: yes

Configure a RADIUS Server now? [YES][no]: no
Warning! The default WLAN security policy requires a RADIUS server.
Please see documentation for more details.

Enter Country Code list (enter ‘help’ for a list of countries) [US]: RU

Enable 802.11b Network [YES][no]: y
Invalid response

Enable 802.11b Network [YES][no]: yes
Enable 802.11a Network [YES][no]: yes
Enable 802.11g Network [YES][no]: yes
Enable Auto-RF [YES][no]: yes

Configure a NTP server now? [YES][no]: yes
Enter the NTP server’s IP address: 172.20.74.29
Enter a polling interval between 3600 and 604800 secs: 10800
Invalid response

Enter a polling interval between 3600 and 604800 secs: 10800

Configuration correct? If yes, system will save it and reset. [yes][NO]: yes

Configuration saved!
Resetting system with new configuration…

Configuration saved!
Resetting system with new configuration…